Enviro Meridian 50-765 Uživatelský manuál Strana 1

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PR

102-3 DAYS/WEEKLY SEASON or 2 TONS OF FUELBurn Pot and Liner Exhaust VentAsh Pan Fresh air Intake TubeInside Firebox Blower MechanismsDoor Glass Heat

HEAT EXCHANGER TUBES (weekly)Open the door and the rod is located under the unit top, in the center of the stove just behind the d

1. Check clearances to combustibles.2. Do not obtain combustion air from an attic, garage, or any unventilated space. Combustion air may be obtained

13InstallationFREESTANDING DIMENSIONS:WIDTH: 24  inches (63.2 cm)HEIGHT: 32  inches (82.6 cm)DEPTH: 24  inches (63.2 cm)

14InstallationINSERT CLEARANCES TO COMBUSTIBLES (INSTALLED IN MASONRY FIREPLACE):The fireplace insert model includes a surround faceplate and a pedest

1. Do not terminate the vent in any enclosed or semi-enclosed areas such as a carport, garage, attic, crawlspace, narrow walkway, closely fenced area

Outside fresh air is mandatory when installing this unit in airtight homes and mobile homes. When connecting to an outside fresh air source, do not us

17The MERIDIAN can be vented through the wall using two different methods. Only use vent of (L or PL) type with an inside diameter of 3 or 4 inches (7

InstallationTHROUGH WALL WITH VERTICAL RISE INSTALLATIONS:Wall framingWall thimbleTermination capVent pipeHorizontal framefor thimble Wa

191.Choose a stove location that is ideal. See the section Deciding Where to Locate Your Pellet Appliance. 2.Place the unit on the hearth pad (if ins

Table of Contents2Introduction...3Pellet Q

1. Lock fireplace damper in the open position.2. Install positive flue connector at the fireplace dampers.3. Connect a Tee or a 90° degree elbow to th

The MERIDIAN can be equipped with an externally mounted exhaust blower (PART #20-070). This optional kit will include all components necessary to inst

22InstallationEXTERIOR MOUNTED EXHAUST BLOWER:TO SUPPLY POWER TO THE EXHAUST BLOWER:Install an amour coated electrical cable from the exhaust blower h

Follow the previous pages for through wall installations. Ensure that vent pipe is properly secured to wall using wall straps. Maintain clearances to

24InstallationMASONRY FIREPLACE INSERT INSTALLATION:The Fireplace insert model requires a surround faceplate and a pedestal. When installing this

Thread hex nut onto the bolt till it is approximately 1” (2.5cm) from the bolt head, slide washer onto bolt. Thread the bolt into the square nut so le

26InstallationASSEMBLY AND INSTALLATION OF INSERT SURROUND PANELS:To assemble the surround panels, lay the panels face down on a soft flat surface and

27InstallationPLATED TRIM INSTALLATION:TO AVOID PERSONAL INJURY DO NOT REMOVE OR REPLACE TRIMS WHEN PELLET STOVE IS HOT! KIT COMPONENTS:TOOLS REQUIRED

TO AVOID PERSONAL INJURY DO NOT REMOVE OR REPLACE COVER WHEN PELLET STOVE IS HOT! TOOLS REQUIRED: ●11/32” socket or wrenchREMOVAL OF DOOR COVER:When s

29DO NOT:● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualifie

PELLET QUALITY IS IMPORTANT, PLEASE READ YOUR ENVIRO PELLET STOVE HAS BEEN DESIGNED TO BURN WOOD PELLETS ONLY. DO NOT USE ANY OTHER TYPE

30üCheck the Exhaust Blower voltage across the blower wires (>=114V on #5 setting and >= 82V on #1 setting). – Replace the Circuit Board if the

31Auger light flashes but auger motor does not turn at all:üIf the Auger gear box does not turn but the motor’s armature does try to spin then the aug

32Wiring Diagram

33Parts ListPart NumberDescription20-040 Control Panel Door50-178 Circuit Board 115V50-179 Circuit Board Decal - 115V50-323 Control Panel Touch Latch5

34MERIDIANSteel Parts based on Freestanding Hopper lid handle50-523Freestandingback grill50-675Top trimPainted50-671Gold50-672Pewter50-673A

35Parts Diagram - Insert SteelMERIDIANSteel Parts based on Insert Top trimPainted 50-671Gold 50-672Pewter 50-673Antique copper 50-674Insert

36MERIDIANCOMPONENTS 200°F (93°C) manual resethigh limit sensorEF-016Convection blower - 115VEF-002Circuit board - 115V50-178AugerEF-025Bra

Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical compon

38The following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:_______________________________

Fuel: This pellet stove is designed and approved to only burn wood pellet fuel with up to 3% ash content. Dirty fuel will adversely affect the opera

Glass: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove with broken glass. The stove uses ceramic glass.

Your pellet Stove has the following safety features:A) The stove will shut off when the fire goes out and the exhaust temperature drops below 120°F (4

7This stove can be placed into two different thermostat modes: HI / LOW OPERATION: If the unit has been placed in the HI / LOW mode. The u

8Operating InstructionsSLIDER/DAMPER SETTING:The slider damper is located behind the left cab side. The door must be open for the cab side to be remov

PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed properly against the ignitor tube for proper operation. Check t