Enviro EG28-120 Uživatelský manuál Strana 1

B Y : S H E R W O O D I N D U S T R I E S L T DOWNER’S MANUALEG28-120EG28 DVSHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS

Maintenance And ServiceFUEL CONVERSION:Figure 9: Removing valve cap.5. Convert the burner orice(s):a) Remove the main burner orice with a  inch de

11Maintenance And Serviceb) Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 10), rotate it counter-

Initial InstallationQUALIFIED INSTALLERS ONLYWARNING: Operation of this heater when not connected to a properly installed and maintained venting syste

VerticalTerminationStorm CollarFlashingRound SupportBox/Wall ThimbleCeiling FirestopPipelengthPipelengthCathedral CeilingSupport BoxPipelengthRound Su

Outside orInside WallOutside WallHoles for screws tohold down the unit.14MOBILE HOME INSTALLATION:• When the unit is installed in a Mobile Home

AADELBCFBBBJMKGHIOpenableFixedClosedOpenableFixedClosedTermination CapAir Supply InletGas MeterGGRestriction Zone(Termination not allowed)NO1 In accor

Figure 19: Wire Spacers.Figure 20: Wire Spacer in Place.the structure. 5. Project a level line from the center point of the elbow. Using

17Initial InstallationQUALIFIED INSTALLERS ONLYFigure 21: Assembly of Venting Kit.Wall framingHorizontal wallterminationWall thimblefire stopInside fi

Initial InstallationQUALIFIED INSTALLERS ONLY1816. Slide the 90° elbow over the ex pipe. Do not slip the outer sections of pipe together, you will re

19Table 4: Vent part numbers (Must state if galvanized or black wanted, PART NUMBERS).Direct Vent GS Direct-Temp Secure Vent Ameri Vent DirectDescrip

FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances must be

Top of EG2810 ft(3.0 m)10 ft(3.0 m)15 ft(4.6 m)15 ft(4.6 m)5 ft(1.5 m)5 ft(1.5 m)20 ft(6.1 m)25 ft(7.6 m)30 ft(9.1 m)33 ft(10.1 m)Figure 23: Vent rest

21HORIZONTAL INSTALLATION:1. Set the appliance in the desired location. Check to determine if wall studs or roof rafters are in the way when the vent

wall thimble will conceal it (see left image in Figure 26).7. Slide the decorative wall thimble up to the wall surface and attach with th

23VERTICAL INSTALLATION:1. Check the instructions for required clearances (air spaces) to combustibles when passing through ceilings, walls, roofs

support straps to the roof. Seal the nails holes heads with non-hardening mastic. Trim the excess length of the support straps that extend out beyond

25NailsCeiling firestopCeilingSecond floorUse clearances to asdefined by appliance andvent pipe manufacturers.• For multi story installations. A

VENTING INTO A CLASS ‘A’ CHIMNEY:This model is also certied and tested to vent into CLASS ‘A’ wood stove chimneys.Place the freestanding direct vent

27Initial InstallationQUALIFIED INSTALLERS ONLYELECTRICAL REQUIREMENTS:The ENVIRO EG28 will operate without electrical power. This model has a millivo

Initial InstallationGAS LINE CONNECTION AND TESTING:WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to t

29Secondary InstallationINSTALLATION OF LOG SET AND EMBERS:The placement of the logs is not arbitrary. If they are positioned incorrectly, t

Table of Contents3Safety Precautions...2Table of Contents...

Secondary InstallationCAUTION: NEVER OPERATE THIS APPLIANCE WITH THE GLASS DOOR REMOVED.3. Place the log set into the rebox. Locate each log by seat

31Trouble ShootingProblem Possible Cause SolutionThe main burner does not ignite when called for.The gas valve may not be on. • Check that the gas

Parts ListReference NumberPart Description Part Number1 120°F (49°C) Ceramic Temperature Sensor EC-0012 Thermocouple EC-0092 Spark Electrode with Cabl

33Parts ListReference Number Part Description Part Number14 Pedestal Door EG28-10915 Burner Tray Top EG28-116ADV Owner’s Manual EG28-12016 Cabinet Sid

Parts Diagram - ChassisEG 28 Body (Chassis) DVApril 200634

35Parts Diagram - Gas Tray & DoorEG 28 Gas Tray and Door AssembliesApril 2006

WarrantySherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to t

37Warranty4. The stove must be operated and maintained at all times in accordance with the instructions in the Owner’s Manual. If the unit shows signs

19. The paint on the Metal Brick Liner may peel. This is due to the extreme conditions applied to the paint during normal usage. It is not a aw and i

39Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________

DIRECT VENT: This type is identied by the sufx DV. This appliance draws all of its air for combustion from outside the dwelling, through a spec

5SpecificationsDIMENSIONS:22"(559 mm)19"(483 mm)11"(279 mm)4"(102 mm)271/2"(699 mm)Shipping Weight 210 lbs (95 kg)Figure 1: E

6Operating InstructionsFOR YOUR SAFETY READ COMPLETELY BEFORE OPERATING.LIGHTING INSTRUCTIONS:Figure 2: Lighting Instructions.Repoussez le bouton et t

ThermopileThermocoupleFigure 4: Gas Valve.Figure 3: Pilot Burning.tips, are not getting enough air. Open the venturi until the ames clean up. If the

Maintenance and ServicePeriodically check to ensure that your direct vent system is clean.Periodically check the pilot and burner. Check to see that a

9Maintenance and ServiceCLEANING PLATED SURFACES:It is important to note that ngerprints and other marks can leave a permanent stain on plated nishe