Enviro Cara Uživatelský manuál Strana 1

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.B Y : S H E R W O O D I N D U S T R I E S

10Figure 9: Install the Rock Set Burner to the Firebox.Maintenance And ServiceRePLacing the gLass:IMPORTANT: Do not operate with the glass front remov

To install the burner:1. Insert the mixing tube into the mixing tube box (refer to Figure 8 or 9).2. When the burner is resting in the rebox en

Maintenance And ServicefueL conveRsion:TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLYPlease read and understand these instructions before installi

13Figure 18: Removing valve cap.Maintenance And Servicescrew must be not visible.Figure 20: Flip valve screw.Red o-ringis not visibleRed o-ringis visi

Initial InstallationQUALIFIED INSTALLERS ONLYWARNING: Operation of this heater when not connected to a properly installed and maintained venting syste

15Initial InstallationQUALIFIED INSTALLERS ONLYPLanning YouR instaLLation:Vertical TerminationStorm CollarFlashingRound Support Box/Wall ThimbleCeili

When planning your installation, it will be necessary to select the proper length of vent pipe for your particular requirements. It is important to no

17Table 6: Vent part numbers (Must state if galvanized or black wanted, PART NUMBERS).Direct Vent GS Direct-Temp Secure Vent Ameri Vent Direct Descri

1 In accordance with the current CSA B149, Natural Gas and Propane Installation Code.2 In accordance with the current ANSI Z223.1 NFPA 54, National Fu

19Initial InstallationQUALIFIED INSTALLERS ONLYvent configuRations anD RestRictoR settings:Figure 28 and 29 shows the range of possible vent congurat

2FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:• All ENVIRO gas-red appliances mu

Initial InstallationQUALIFIED INSTALLERS ONLYRestRictoR instaLLation:The ENVIRO CARA has been designed for use with an add-in restrictor. The restrict

21WoodscrewsWall ThimbleStrapSheet metal screwsFold strap here11/4" (3.2cm)Figure 33: Installing Decorative Wall Thimble.10"(254mm)10"(

Initial InstallationQUALIFIED INSTALLERS ONLYWood screws (x4)Cut vinyl sidingaway to fit standoffBolt (x4)requiredNut (x4)requiredWoodscrew (x4)Figure

23attic, as well as above the roof line. The galvanized nish is desirable above the roof line, due to the higher corrosion resistance.6. Once the pip

8. Continue to add pipe sections until the height of the vent cap meets the minimum code requirements. Refer to Figure 38 and Table 6. Note that for

25plumber’s tapeconnected towall strapWall strap45° elbows (x2)NailsCeiling firestopCeilingSecond floorUse clearances to asdefined by appliance andven

Figure 42: Cathedral Ceiling Support Box Installation.Initial InstallationQUALIFIED INSTALLERS ONLYFigure 43: Corner installation rear vented with sno

27Vent PipeInside Finished CollarDry WallWall ThimbleExterior WallSidingMinimum Vent Terminal 36”(914mm) High Snorkel Kit.Figure 46: Installation for

Vent CapInside Finished CollarCeiling SupportInsulation GuardFlue PipeRoof TrussRoof FlashingInitial InstallationQUALIFIED INSTALLERS ONLYinstallation

29Initial InstallationQUALIFIED INSTALLERS ONLYgas line connection and testing:WARNING: Only persons licensed to work with gas piping may make the nec

Table of Contents3Safety Precautions...

Initial InstallationQUALIFIED INSTALLERS ONLYelectrical requirements for gas ValVe and optional Blower:The ENVIRO CARA will operate without electrical

31Figure 52: Optional Blower (Fan) Installation.1. Remove the pre-assembled blower from the packaging. Inspect the blower for damage. If damage is no

32Initial Installationcommonwealth of massachusetts installation adendum:These are the Special Requirements for Side-Wall Vented Appliances in Commonw

33Initial Installation(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4: 1. The equipment listed in Chapter 10 en

Figure 55: Log Placement of Right Log.The placement of the logs is not arbitrary. If they are positioned incorrectly, the ames can be “pinched” and w

35Secondary InstallationSecondary InstallationFigure 58: Log Placement Complete.Figure 56: Log Placement of Left Log.Left LogCenter LogFigure 57: Log

InstallatIon of Rock set:If the rocks are positioned incorrectly, the ames can be “pinched” and will not burn correctly. If the rocks are broken due

37Secondary InstallationFigure 61: Rock Placement of Four Large Rocks.Figure 62: Rock Placement of Two Medium Rocks.Figure 63: Rock Placement of Seven

Secondary InstallationImportant note: When the unit is turned on for the rst time, it should be turned onto high without the fan on for the rst four

39Trouble ShootingProblem Possible Cause SolutionThe main burner does not ignite when called for.The gas valve may not be on. • Check that the gas

4DIRECT VENT ONLY: This type is identied by the sux DV. This appliance draws all of its air for combustion from outside the dwelling, through a spec

Parts List40Reference NumberPart Description Part Number1 120°F (49°C) Ceramic Fan Temperature Sensor EC-001Thermopile EC-0122 S.I.T. Piezo Igniter EC

41Parts ListReference NumberPart Description Part Number9 Cara Door Latch Assembly 50-159410 Cara Main Orice NG (PO512-37) 50-159610 Cara Main Orice

Parts Diagram42

43WarrantySherwood Industries Ltd. is the manufacturer of the VistaFlame line of heating products. At Sherwood Industries, our commitment to the highe

4. The stove must be operated and maintained at all times in accordance with the instructions in the Owner’s Manual. If the unit shows signs of negle

4520. Sherwood Industries Ltd. is free of liability for any damages caused by the replace or stove, as well as inconvenience expenses and materials.

46Installation Data SheetThe following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:________

5SpecificationsWARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxid

6Operating InstructionsFor Your Safety, Read Safety Precautions And Lighting Instructions Before Operating.WARNING: IF YOU DO NOT FOLLOW THESE INSTRUC

7aiR shutteR:Air Shutter Adjustment NutFigure 5: Air Shutter Adjustment.The air shutter is controlled by sliding the air shutter adjustment s

Operating InstructionsFor Your Safety, Read Safety Precautions And Lighting Instructions Before Operating8The ideal ame will be blue at the base and

9Maintenance And ServiceRoutine maintenance:At least once a year, run through the following procedures to ensure the system is clean and working prope